자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to fix door hinge a Loose composite door hinges Hinge

Fixing a loose door hinge is a simple task for the majority of homeowners. If the screws' holes have been smashed and will not hold screws, you could need to use dowels and wood glue to fix the door hinge.

Before you do that though, brush away the surface rust. This will allow the dowels to remain in place and provide them a solid foundation to rest on.

Take off the Hinges

Most hinges on doors can be removed, which makes it easier to move the door from one side to the next or to take the entire door off of the frame if need be. The removal of the hinges is easy for anyone with patience, although you need to know how do it right.

If the hinges are painted you will need to remove the paint before attempting to remove the pins. If you do not, the paint may flake off and scratch the door when you attempt to lift it. To break the seal put the hinges in a stainless steel pan and fill the pan with water until the hinges are completely submerged. The hinges should remain in the pan for approximately 30 minutes. The heat from the water will soften the paint and make it easier to remove the pins.

After the pins have been loosen, you can remove the hinges from the door and frame. It is possible to use a standard screwdriver, but it is recommended to use a magnetic screwdriver for this task. This type of screwdriver was created to pick up screws made of metal and make the task run much more quickly.

Before you attempt to remove the hinges it is a good idea to spray them with oil. A simple lubricant will allow you to move the process along faster and also remove the pins and screws with ease. This kind of lubricant is able to be found at most hardware stores as well as home improvement shops.

The number of hinges needed will also depend on what type of door you have and the way it's installed. Heavier and solid-cored doors will require more hinges while hollow-cored doors that are lighter may only require two or three hinges.

It is also important to understand the different types of hinges so you can decide which one will be the most effective for your particular situation. Exterior hinges are designed to hold the weight of a door, but hinges for interior use must be able to handle heavier loads.

Reattaching the Hinges

Sometimes a door hinge will loosen over time and start to hang crookedly or sag. This can cause problems, but it's usually easy to repair. In most cases it's a simple tightening of the screw will solve the problem. However when the screw holes are stripped out, this may be more difficult. Fortunately, there is a method to make these holes back to their original size that uses a wood dowel.

Start by drilling out the hole you had previously made using a drill bit that is close to the size of the new screw (typically 3/8"). Then, you can use wood glue and a dowel made of wood to fill the hole. To ensure a secure fit, the dowel should be cut to the same length as the screw. Reinstall the screw and tighten it to the desired degree of tightness. If the door does not stop bind up, insert a second dowel into the gap. Repeat the process. Make sure to close the door slowly so that you can examine the clearances around the perimeter after each adjustment.

You can also use a wooden plug instead of the dowel. This will work equally well, but may take a little longer to set up. You can insert the wood piece that has been whittled to the proper size. If you don't own an instrument for woodworking or toothpicks, you can make use of toothpicks or matchsticks made of wood.

After you've reinstalled your new screw, use a countersink bit to make the hole for the head of the screw smaller, so that it doesn't rub against the edge of the door when it's open and closed. This will make it much easier to tighten the screws before replacing hinges.

After reinstalling the hinge, make sure to lubricate the hinge using an oil-based lubricant that is dry. This will help prevent it from getting stuck in the future. You can use products such as PB Blaster and Liquid Wrench. Apply a thin layer and allow it to soak into the barrel of the hinge for approximately 15 minutes.

Refinishing the Hinges

If you're not sure if you're ready to replace the hinges on your door, you can make a few repairs. Verify that the screws that hold the hinge plate in place to the door frame and frame are tight. If they're loose, tighten them using an electric drill or screwdriver. Be cautious not to tighten the screws so tight that they cause gaps at the trim joints, or worse cause threads to be stripped.

If the problem is the hinge plates are separating, you can reattach the plates by applying wood glue to the back of them and then inserting toothpicks or wooden dowels into the holes. The toothpicks and dowels provide an solid foundation for the screws, preventing the plates from shifting when you push them in. Allow the glue to dry before reattaching the hinge.

The screws may also be stripped or missing. This can be fixed by replacing the screws with larger ones. Use a drill bit that is the same size as the screw hole to avoid drilling into the jamb or hinge.

After you've reattached your hinge close the door and look at the gap between the door and the frame. The gap should be the thickness of a penny all around or less if an old door was not hung correctly. This should not be a problem if the hinges are correctly installed.

If the hinges seem loose, you can add a stronger hinge between the hinge plate's surface and the mounting surface. This will give the hinges more space. You can also take off the hinge pin and pound it down with a hammer in order to tighten it, or install a new hinge. You can also lubricate your hinges using mineral or jojoba oil to reduce upvc friction hinges and aid in holding their place. Lubricating your hinges periodically will prevent them from becoming stiff and squeaky, and also prolong their lifespan.

Cleaning the Hinges

The constant movement of a hinge causes friction, which attracts dust particles. These particles can become stuck and accumulate in the moving parts of door double glazing hinges if they are not maintained and cleaned regularly. As a result the upvc window hinge problems can become stiff and creaky, and its appearance can get worse. Regular cleaning, lubrication, and inspections will maintain the functionality and quality of hinges on a door.

Examine the hinges for signs of corrosion. If the rust has corroded to the point of destroying surface of the hinge barrel or screw holes, you'll require replacement of the hinges. If you are able to save the hinges, remove any loose rust using wire brush and steel wool. Apply a commercial rust-removing product or a homemade solution such as lemon juice on the hinge. Let the rust removal solution remain on the hinge for a few minutes to dissolve and penetrate any remaining corrosion.

Retightening screws can help restore hinge function in the event that you don't want to spend money or time to replace hinges. If you have stripped the screws, however, it may be necessary to attach a wooden dowel or shim to the hinge. Dowels made of wood come in round rods of varying lengths and sizes. You can buy them on the internet, at woodworking supply stores and at home improvement stores.

A shim may be made of plastic or metal, based on the kind of hinge you've got. To make a dowel cut a piece of wooden dowel or another sturdy material to the desired size. You can dip the dowel in carpenter's glue and then insert it into the hole. The glue will hold the dowel securely in place.

Before cleaning the hinges put down a piece of paper cloth or towel to protect your flooring from spills. Once the area is protected and dry, clean the hinges with an absorbent sponge or a soft cloth that has been soaked in mild cleaner or vinegar to remove dirt, grime, and tarnish. You can use a toothbrush or small brush to reach hard-to-reach spots in crevices and tight areas.