자유게시판

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

how to replace subaru key fob to Change a Subaru Spare Key

If you lose your Subaru car key, call a locksmith. Locksmiths will usually cut you a key cheaper than the dealer.

Subaru car keys are typically either intelligent "push-to-start" fob remote keys or plain keys made of metal. The Fob key has a chip in it and requires reprogramming.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your car or the lift gate. The remotes use an inside keypad to connect to the computer system in your vehicle.

Certain models of Subaru offer a less-known feature called PIN Code Access. You can utilize a personalized number sequence to start and open your car. Refer to the owner's manual for learn how to use this feature if you own a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.

If your keys stop working, there's an excellent possibility that the battery inside the key fob is dying. You can test the battery life of your key fob with an electronic tester that you can carry around or a multimeter in your garage.

The next step is to take the key fob out of its case and inspect the circuit board of its transmitter. You'll be able to see one or two sets of eight-digit numbers. Note the first set so you can remember it. After you've completed that take the key fob back together and you'll be able to program it at home. The procedure for programming will vary based on the type and year of your vehicle but it's generally simple enough to complete by yourself.

Key Fobs

Subaru's most recent models include key fobs that can not only unlock doors but also turn on lights, lock gas cap and even start the car. This feature is especially helpful if you've been at a gas station and your car wouldn't even start because the battery inside the key fob has gone out.

No matter if your Subaru is old or new, it's likely that the key fob can be replaced without difficulty. Remember that some of the most modern models, with the latest technology, might require an appointment with the dealer. But, with a bit of time and effort, you can get your new key fob to use at home.

Start by examining the circuit board that controls the transmitter on your key fob (instructions to open the case should be included in your owner's manual). There should be two or more serial numbers of 8 numbers each. Keep the first set of numbers in your wallet for later information.

Then, you'll need to get into the driver's seat and close the doors. Turn the key ten times to start your car, then switch off the engine. Press the lock button on your key fob and open the door to ensure that all of your doors are working properly. Then shut the door and take the key out of the ignition. The car should buzz again, which indicates that the key fob has been programmed.

Ignition System

The key battery could be dead If your Subaru keys aren't functioning as they should. If you know how to reprogram a subaru key fob, you could replace the key fob's battery yourself. The replacement key subaru of the battery is affordable and easy to locate. If the key fob doesn't respond to your commands, it could be a different problem. It is recommended to visit a dealer for an extra key. They will guarantee that the key is genuine Subaru key that's under warranty. It will also be programmed to your vehicle. This is much simpler and safer than getting an aftermarket key from a business online.

The dealer will also cut keys for you if you provide them with your VIN number as well as proof of ownership. This information is used to identify the replacement key so that it is accepted by your immobilizer. This is a more complicated process than cutting a key, and the dealership will charge you more.

Once the new key is programmed, you are able to switch it into your working key. You'll only have five seconds to insert the second key, which is why it's crucial to keep a working key on hand. You can take the key off after the security light has stopped flashing and test it.

Battery Replacement

One of the key features that make Subaru fobs so beneficial is their ability to turn on your car's power windows as well as sunroof with a single touch of the button. But, the battery in your subaru replacement key fob isn't intended to last forever, and will eventually need to be replaced. It's good news that replacing the battery is a straightforward process that you can do yourself with the help of this short guide from Capitol Subaru.

First, you'll need to locate the small crevice that is the gap between the front and back of your keyfob. Utilizing a small flathead screwdriver, you can break the seam to reveal a small space inside that houses the battery. Remove the old battery and then install a new one, ensuring that it is facing the correct side upwards. Once you have assembled everything and you are ready to use the new key fob to lock the vehicle, unlocking it, and then starting your vehicle.

It's always a good idea to have an additional set of keys at hand particularly if you've lost yours or it's not functioning properly. A new key can be bought at your local auto dealer, or you can have one cut from an locksmith. Whatever you choose, it's essential to get your key fob functioning properly as soon as you can so that you can drive in a safe manner!